搅拌车载泵常见几点的保养办法 首页 > 平台公告

作者:百农机械网   发布日期:2019-12-09 12:24:22

搅拌车载泵常见几点的保养办法

  二手搅拌车载泵的运用和保管过程中,因为机件磨损、天然腐蚀和老化等原因,其技术性能将逐渐变坏,有必要及时进行保养和修理。拌和车载泵保养的目的是康复混凝土泵车的正常技术状况,坚持良好的运用性能和可靠性,延长运用寿命;减少油料和器材消耗;避免事端发生,保证行驶和作业安全,进步经济效益和社会效益。下面和小编一起来了解拌和车载泵有哪些保养和保护办法。
  拌和车载泵保养
  1.清洁车容整齐,发动机及各总成部件和随车东西无污垢,各滤清器正常运用,液压油、机油无污染,各管路四通八达。
  2.查看发动机和各总成、部件状况正常。机件完全可靠,各连接、紧固件完好。
  3.紧固各紧固件有必要完全无损坏,安装可靠,紧固程度符合要求。
  4.调整了解各部件调整的技术要求,依照调整的办法、步骤,认真细致地进行调整。
  5.光滑依照不同地区和时节,正确挑选光滑剂种类,加注的油品和东西应清洁,加油口和油嘴应擦洗干净,加注量应符合要求。
  拌和车载泵的保护
  1.底盘部分的保护底盘的查看主要有油、水的查看;离合器、变速器、轮胎的查看。
  2.分动箱及反转减速机的保护定时三个月给反转减速机构与反转之承连接的小齿轮外表涂改光滑脂,定时通过加油座上的光滑嘴用油枪给反转轴承加注光滑脂。
  3.泵送设备的保护设备泵送5000m3左右混凝土后,应注意查看眼镜板与切开环间的空隙,若超过2mm,且磨损均匀,则应考虑调整空隙。
  4.液压系统的保护清洁是液压系统保护的重要工作。经常清洗才干保证系统没有尘埃、赃物及其他颗粒。查看液压软管及接头是否有渗漏油现象,若有损坏则有必要更换液压软管。
Maintenance methods of mixing truck pump



In the process of using and keeping the second-hand truck mounted agitator pump, its technical performance will gradually deteriorate due to wear, natural corrosion, aging and other reasons, so it is necessary to maintain and repair it in time. The purpose of mixing truck pump maintenance is to recover the normal technical condition of concrete pump truck, adhere to good operation performance and reliability, extend the service life, reduce oil and equipment consumption, avoid accidents, ensure driving and operation safety, and improve economic and social benefits. Let's learn about the maintenance and protection methods of the mixing truck pump together with Xiaobian.

Mixing truck pump maintenance

1. Clean the vehicle in order. The engine and all assembly parts and accompanying things shall be free of dirt. All filters shall be in normal operation. Hydraulic oil and engine oil shall be free of pollution. All pipelines shall be in all directions.

2. Check whether the engine, assemblies and components are in normal condition. The parts are completely reliable, and all connections and fasteners are in good condition.

3. It is necessary to fasten all fasteners without any damage. The installation is reliable and the fastening degree meets the requirements.

4. Adjust and understand the technical requirements of each component adjustment, and adjust carefully according to the adjustment methods and steps.

5. According to different regions and seasons, the type of smooth agent shall be selected correctly. The oil products and things to be filled shall be clean, the oil filler and nozzle shall be cleaned, and the filling amount shall meet the requirements.

Protection of mixing truck pump

1. The inspection of the protective chassis mainly includes the inspection of oil and water; the inspection of clutch, transmission and tire.

2. The transfer case and reverse gear unit shall be protected for three months to apply smooth grease to the surface of the pinion connected with the reverse gear reducer and the reverse gear bearing, and the reverse bearing shall be filled with smooth grease regularly through the smooth nozzle on the oil filling base with an oil gun.

3. After the protection equipment of the pumping equipment pumps about 5000m3 of concrete, pay attention to check the gap between the spectacle plate and the cutting ring. If the gap is more than 2mm and the wear is even, the gap should be adjusted.

4. The protection and cleaning of hydraulic system is an important work of hydraulic system protection. Regular cleaning can ensure that the system is free of dust, dirt and other particles. Check the hydraulic hose and connector for oil leakage. If there is any damage, it is necessary to replace the hydraulic hose.

相关资讯

百农-让每位客户都能拥有更好的二手混凝土设备

全国地区设备查询:152-1114-2288(工作时间:全天24小时候机)